I have already written an article to check the network bandwidth speed using netperf available at below link
How to monitor network bandwidth in Linux using netperf
In this article I will guide you the steps to be used to monitor the available network bandwidth using iperf3.
One advantage here you have with iperf3 that it is a part of the Red Hat Vanilla DVD and you need not download any third party tool.
Below steps are validated on Red Hat Enterprise Linux 7
You can install the iperf3 using yum command assuming you have a valid repository or you can copy the rpm from the Red Hat DVD and install it manually
NOTE: On RHEL system you must have an active subscription to RHN or you can configure a local offline repository using which "yum" package manager can install the provided rpm and it's dependencies.
The latest version of the iperf source code is at https://github.com/esnet/iperf
With the below list of steps the iperf sets a large send and receive buffer size to maximise throughput, and performs a test for 60 seconds which should be long enough to fully exercise a network.
On Server (IP: 10.58.160.101)
# yum install iperf3
OR
# rpm -Uvh /home/deepak/iperf3-3.1.7-2.el7.x86_64.rpm
warning: /home/deepak/iperf3-3.1.7-2.el7.x86_64.rpm: Header V3 RSA/SHA256 Signature, key ID fd431d51: NOKEY
Preparing... ################################# [100%]
Updating / installing...
1:iperf3-3.1.7-2.el7 ################################# [100%]
Explanation of the switches used:
-i, --interval n
pause n seconds between periodic bandwidth reports; default is 1, use 0 to disable
-s, --server
run in server mode
Run the below command on the server
server # iperf3 -i 10 -s
warning: this system does not seem to support IPv6 - trying IPv4
-----------------------------------------------------------
Server listening on 5201
-----------------------------------------------------------
Accepted connection from 10.58.160.103, port 40614
[ 5] local 10.58.160.101 port 5201 connected to 10.58.160.103 port 40616
[ ID] Interval Transfer Bandwidth
[ 5] 0.00-10.00 sec 1.27 GBytes 1.09 Gbits/sec
[ 5] 10.00-20.00 sec 1.27 GBytes 1.09 Gbits/sec
[ 5] 20.00-30.00 sec 1.27 GBytes 1.09 Gbits/sec
[ 5] 30.00-40.00 sec 1.27 GBytes 1.09 Gbits/sec
[ 5] 40.00-50.00 sec 1.27 GBytes 1.09 Gbits/sec
[ 5] 50.00-60.00 sec 1.27 GBytes 1.09 Gbits/sec
[ 5] 60.00-60.04 sec 4.78 MBytes 1.04 Gbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth
[ 5] 0.00-60.04 sec 0.00 Bytes 0.00 bits/sec sender
[ 5] 0.00-60.04 sec 7.63 GBytes 1.09 Gbits/sec receiver
-----------------------------------------------------------
Server listening on 5201
-----------------------------------------------------------
Accepted connection from 192.169.173.7, port 35190
[ 5] local 192.169.173.5 port 5201 connected to 192.169.173.7 port 35192
[ ID] Interval Transfer Bandwidth
[ 5] 0.00-10.00 sec 3.55 GBytes 3.05 Gbits/sec
[ 5] 10.00-20.00 sec 3.59 GBytes 3.08 Gbits/sec
[ 5] 20.00-30.00 sec 3.59 GBytes 3.08 Gbits/sec
[ 5] 30.00-40.00 sec 3.59 GBytes 3.08 Gbits/sec
[ 5] 40.00-50.00 sec 3.59 GBytes 3.08 Gbits/sec
[ 5] 50.00-60.00 sec 3.59 GBytes 3.08 Gbits/sec
[ 5] 60.00-60.04 sec 14.4 MBytes 3.14 Gbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth
[ 5] 0.00-60.04 sec 0.00 Bytes 0.00 bits/sec sender
[ 5] 0.00-60.04 sec 21.5 GBytes 3.07 Gbits/sec receiver
-----------------------------------------------------------
Server listening on 5201
By default the server will use TCP port 5201, if you intend to use some other port use "-p" switch
-p, --port n
set server port to listen on/connect to to n (default 5201)
On Client (192.169.173.7, 10.58.160.103)
# rpm -Uvh /tmp/iperf3-3.1.7-2.el7.x86_64.rpm
warning: /tmp/iperf3-3.1.7-2.el7.x86_64.rpm: Header V3 RSA/SHA256 Signature, key ID fd431d51: NOKEY
Preparing... ################################# [100%]
Updating / installing...
1:iperf3-3.1.7-2.el7 ################################# [100%]
Explanation of the switches used:
-i, --interval n
pause n seconds between periodic bandwidth reports; default is 1, use 0 to disable
-w, --window n[KM]
window size / socket buffer size (this gets sent to the server and used on that side)
-t, --time n
time in seconds to transmit for (default 10 secs)
-c, --client host
run in client mode, connecting to the specified server
Run the below command wherein the IP with -c is the server IP (eth0)
client # iperf3 -i 10 -w 1M -t 60 -c 10.58.160.101
Connecting to host 10.58.160.101, port 5201
[ 4] local 10.58.160.103 port 40616 connected to 10.58.160.101 port 5201
[ ID] Interval Transfer Bandwidth Retr Cwnd
[ 4] 0.00-10.00 sec 1.27 GBytes 1.09 Gbits/sec 0 2.30 MBytes
[ 4] 10.00-20.00 sec 1.27 GBytes 1.09 Gbits/sec 0 2.30 MBytes
[ 4] 20.00-30.00 sec 1.27 GBytes 1.09 Gbits/sec 0 2.30 MBytes
[ 4] 30.00-40.00 sec 1.27 GBytes 1.09 Gbits/sec 0 2.30 MBytes
[ 4] 40.00-50.00 sec 1.27 GBytes 1.09 Gbits/sec 0 2.30 MBytes
[ 4] 50.00-60.00 sec 1.27 GBytes 1.09 Gbits/sec 0 2.30 MBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-60.00 sec 7.63 GBytes 1.09 Gbits/sec 0 sender
[ 4] 0.00-60.00 sec 7.63 GBytes 1.09 Gbits/sec receiver
iperf Done.
Another attempt using a different interface (eth2)
client # iperf3 -i 10 -w 1M -t 60 -c 192.169.173.5
Connecting to host 192.169.173.5, port 5201
[ 4] local 192.169.173.7 port 35192 connected to 192.169.173.5 port 5201
[ ID] Interval Transfer Bandwidth Retr Cwnd
[ 4] 0.00-10.00 sec 3.56 GBytes 3.06 Gbits/sec 0 2.10 MBytes
[ 4] 10.00-20.00 sec 3.59 GBytes 3.08 Gbits/sec 0 2.10 MBytes
[ 4] 20.00-30.00 sec 3.59 GBytes 3.08 Gbits/sec 0 2.10 MBytes
[ 4] 30.00-40.00 sec 3.59 GBytes 3.08 Gbits/sec 0 2.10 MBytes
[ 4] 40.00-50.00 sec 3.59 GBytes 3.08 Gbits/sec 0 2.10 MBytes
[ 4] 50.00-60.00 sec 3.59 GBytes 3.08 Gbits/sec 0 2.10 MBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-60.00 sec 21.5 GBytes 3.08 Gbits/sec 0 sender
[ 4] 0.00-60.00 sec 21.5 GBytes 3.08 Gbits/sec receiver
iperf Done.
Lets check the allowed bandwidth speed for each of this interface
The first attempt was done using eth0
# ethtool eth0 | grep Speed
Speed: 1000Mb/s
The second attempt was done using eth2
# ethtool eth2 | grep Speed
Speed: 3000Mb/s
So as we see the allowed bandwidth for eth0 was 1 Gb and we had a bandwidth speed of almost 1.09Gb/s
while for the other interface we had an allowed bandwidth of 3 Gb/s wherein the bandwidth throughput reached 3.08 Gb/s
I hope this article was useful.